10L80 Valve Body Diagram: Gen 1, Gen 2 & Gen 3 Guide

10L80 Valve Body Diagram: Gen 1, Gen 2 & Gen 3 Guide

Nathaniel ValentinNovember 17, 2026

Prefer to print? Download the printable 10L80 Valve Body Diagram PDF — article and original diagrams.

DRIVETRAIN 101 · ORIGINAL KIT INSTRUCTION DIAGRAMS

A useful 10L80 valve body diagram starts with the correct generation and shift configuration. This guide groups the original Next Gen Drivetrain® GM 10L illustrations into Gen 1, Gen 2 mechanical shift, Gen 2 electronic shift and Gen 3 electronic shift sections, with a printable PDF containing the same diagrams.

Application note: The kit listing covers the GM 10L60/10L80/10L90 family. Diagram applicability depends on generation, shift configuration and kit variant. Dedicated applications, including the separately listed Camaro option, require confirmation against the exact order and instructions.

1. Choose the correct generation and instruction guide

Start with the separator plate and assembled valve body, then identify whether the vehicle uses mechanical or electronic shift operation. A similar casting outline does not establish that checkballs, manual-valve components or separator plates are interchangeable.

The guide-selection table below follows the current product listing and the manuals’ identification pages. The Gen 2 and Gen 3 manuals state that they apply to kits purchased after July 1, 2026. Use the guide supplied for an earlier kit.

Configuration Source guide
2017-2018 Gen 1 mechanical shift G10L-VBUK1
2019-2024 Gen 2 mechanical shift G10L-VBUK3
2019-2024 Gen 2 electronic shift G10L-VBUK3 manual; G10L-VBUK4 kit
2025 and newer Gen 3 electronic shift G10L-VBUK6

2. Gen 1: latch valves and mechanical-shift layout

The Gen 1 upper diagram identifies latch valves A, B, C and F, plus the pressure-regulator, TCC-regulator, lube-control, lube-regulator and cooler circuits. The lower drawing names the SRVs, line-pressure control circuit and accumulator/damper locations.

The assembled view supplies the bolt legend, pump-seal location, temperature sensor and plate identifiers. The manual includes conditional labels for configurations; use the Gen 1 mechanical-shift identification and actual casting together rather than assuming every label describes every unit.

10L80 Valve Body Diagram: Gen 1 upper view: four latch valves and the pressure, TCC, lube and cooler circuits.
Diagram 1. Gen 1 upper view: four latch valves and the pressure, TCC, lube and cooler circuits. Source: G10L-VBUK1 instructions, PDF page 6.Open full-size diagram.
10L80 Valve Body Diagram: Gen 1 lower-body reference: SRVs and accumulator/damper locations.
Diagram 2. Gen 1 lower-body reference: SRVs and accumulator/damper locations. Source: G10L-VBUK1 instructions, PDF page 7.Open full-size diagram.
10L80 Valve Body Diagram: Gen 1 assembled view: bolt map, plate identification, temperature sensor and pump seal.
Diagram 3. Gen 1 assembled view: bolt map, plate identification, temperature sensor and pump seal. Source: G10L-VBUK1 instructions, PDF page 8.Open full-size diagram.

3. Gen 2 mechanical shift: upper and lower layouts

The Gen 2 mechanical-shift upper diagram identifies low and high feed-limit valves, pressure and TCC regulators, the boost valve and sleeve, lube/cooler circuits and default-control valves. It also marks checkball locations in red.

The corresponding lower diagram shows the mechanical manual valve, SRVs A-F, the TCC-priority valve and the numbered dampers. Preserve the orientation notes, including the spring-up note at damper 5. The assembled bolt map is a separate reference from these internal valve drawings.

10L80 Valve Body Diagram: Gen 2 assembled valve body and fastener legend.
Diagram 4. Gen 2 assembled valve body and fastener legend. Source: G10L-VBUK3 instructions, PDF page 6.Open full-size diagram.
10L80 Valve Body Diagram: Gen 2 mechanical-shift upper valve body and checkball locations.
Diagram 5. Gen 2 mechanical-shift upper valve body and checkball locations. Source: G10L-VBUK3 instructions, PDF page 7.Open full-size diagram.
10L80 Valve Body Diagram: Gen 2 mechanical-shift lower valve body, manual valve, SRVs and dampers.
Diagram 6. Gen 2 mechanical-shift lower valve body, manual valve, SRVs and dampers. Source: G10L-VBUK3 instructions, PDF page 8.Open full-size diagram.

4. Gen 2 electronic shift: use the matching pair

The electronic-shift upper and lower drawings are a separate pair in the same guide. The lower view identifies the electronic manual-valve assembly and ETRS valve, along with the default solenoid and auxiliary fluid-pump seal.

Use the checkball positions and component notes from the electronic-shift pair. Do not mix a lower-body diagram from one shift configuration with the upper diagram or separator plate from another simply because the transmission model is the same.

10L80 Valve Body Diagram: Gen 2 electronic-shift upper valve body.
Diagram 7. Gen 2 electronic-shift upper valve body. Source: G10L-VBUK3 instructions, PDF page 9.Open full-size diagram.
10L80 Valve Body Diagram: Gen 2 electronic-shift lower valve body, electronic manual-valve assembly and ETRS valve.
Diagram 8. Gen 2 electronic-shift lower valve body, electronic manual-valve assembly and ETRS valve. Source: G10L-VBUK3 instructions, PDF page 10.Open full-size diagram.

5. Gen 3: electronic-shift assembly and revised circuits

The Gen 3 assembled drawing identifies the default-disable, line-pressure and TCC solenoids, electronic manual-valve actuator location, temperature sensor, main pump seal and auxiliary-pump connection. Use this bolt map for the matching generation.

The Gen 3 upper drawing identifies the feed-limit valve, pressure regulator, boost assembly, default-control valves, lube regulator and TCC regulator. The lower drawing shows the ETRS valve, SRVs, dampers and a checkball reminder in the inset view.

The guide specifically restricts service of the ETRS valve to a trained professional. Use the drawing for identification and follow that instruction when deciding the scope of disassembly.

10L80 Valve Body Diagram: Gen 3 assembled view: bolt map, solenoids, seals and electronic manual-valve actuator location.
Diagram 9. Gen 3 assembled view: bolt map, solenoids, seals and electronic manual-valve actuator location. Source: G10L-VBUK6_Instructions_26.07.24_compressed instructions, PDF page 6.Open full-size diagram.
10L80 Valve Body Diagram: Gen 3 upper valve body and red checkball locations.
Diagram 10. Gen 3 upper valve body and red checkball locations. Source: G10L-VBUK6_Instructions_26.07.24_compressed instructions, PDF page 7.Open full-size diagram.
10L80 Valve Body Diagram: Gen 3 lower valve body: SRVs, ETRS valve, dampers and checkball inset.
Diagram 11. Gen 3 lower valve body: SRVs, ETRS valve, dampers and checkball inset. Source: G10L-VBUK6_Instructions_26.07.24_compressed instructions, PDF page 8.Open full-size diagram.

6. Checkballs, plates and kit selection

The Gen 2 and Gen 3 drawings label red checkballs as 0.250 inch. Follow both halves of the correct diagram pair and keep every small part associated with its original location. Color coding from another transmission’s guide is not a substitute for the legend here.

The Next Gen Drivetrain® kit components differ across generations. Gen 1 latch-valve parts, Gen 2 feed-limit components and the Gen 3 arrangement should not be treated as one universal kit. Confirm the variant on the product page and follow its linked installation procedure.

The full manuals also explain separator-plate and OEM cover-plate stacking, torque, fluid service and final checks. Those steps remain necessary after the valve and checkball locations have been identified.

7. Frequently asked questions

7.1 Is one 10L80 diagram correct for every year?

No. The linked manuals distinguish three generations and, within Gen 2, mechanical and electronic shift layouts. Start with the identification table.

7.2 Are 10L60 and 10L90 diagrams included?

The Gen 2 and Gen 3 drawings identify the 10L60/10L80/10L90 family. Confirm the specific application and kit variant; a family name does not guarantee every plate or component is interchangeable.

7.3 Which drawing shows the pump seal?

The assembled views identify the pump-seal location. Gen 2 and Gen 3 drawings also include auxiliary fluid-pump sealing details where applicable.

8. Kit and complete installation instructions

Find the matching kit and installation guide

Use the current product listing to confirm application and kit contents. Follow the complete instructions for disassembly, installation, torque and final checks.

View the 10L80 Valve Body upgrade kit

Use these guides to connect the component locations above with symptoms, diagnosis and upgrade choices.

Prepared from the linked Next Gen Drivetrain® instructions and product listing on November 17, 2026. Original diagram labels are preserved; some pages are rotated for reading. This educational reference accompanies the complete kit instructions. © Next Gen Drivetrain. All rights reserved.

Leave a comment

Please note, comments must be approved before they are published